See what our Experts say about this CE Smith Trailer Hubs and Drums

• Replacement Hubs for 2,700 lb Axle
  Based on your photo it looks like you have 2,700 lb axles, and we do have hubs for that size axle. However, you will need to confirm the bearings your current hub has. You will need to take apart your current hub assembly and look at the bearings themselves; wipe away the grease and you should be able to see the part number stamped directly on them. If you are unable to find them, you need to use a digital caliper to measure your spindle to the thousandths of an inch where the bearings...
  view full answer...
  
• Replacement Hubs for a Triton 08351 PWC Trailer Axle
  Yes, I am and thanks for the information. It looks like your Reliable 2700lb Torsion Axle 08351 has a 1-1/16" x 1-1/16" spindle. I have two options for replacements and which one you need is going to be determined by how big your PWC trailer's wheels are. I have listed the two options below; 13" to 14" Wheels - CE Smith Trailer Idler Hub Assembly w/ Case for 2.7K Axles - 5 on 4-1/2 - Galvanized - Pre-Greased - item # CE13315 8", 10", 12" Wheels - Dexter Trailer Idler Hub Assembly for...
  view full answer...
• Replacement Hub for Load Rite 19R20 Trailer
  Hi Don; I wasn't able to find anything with the model number and even if I could, I would only be guessing at the axle size for a replacement hub. You will need to identify your axle to find the right hub. You can either look for an axle tag or pull the existing hubs off to check bearings. Then you can look for the bearing part numbers or measure the inner diameter with a digital caliper # PTW80157. The # 8-258-50UC1-EZ you asked about is designed for 2,200 lb axles with # L44649 inner...
  view full answer...
• Replacement 5-Lug Idler Hubs for 1992 Spectrum Boat Trailer with L44649 Bearings
  Hey Clyde, thanks for reaching out! From everything you described you're needing the CE Smith Trailer Idler Hub Assembly w/ Case for 2.7K Axles # CE13315. This comes pre-greased and in a protective case for shipping. The 5 on 4-1/2" bolt pattern is standard for this size axle so it may be that you just measured a little different on your end. If you check out the linked helpful article on bolt patterns you can verify whether or not what we have matches what you have. Let me know if you...
  view full answer...
• Recommended Hub w/ a 5 on 4-1/2" Bolt Pattern that Fits a BTR Spindle w/ L44649 Bearings
  Thank you for all of the detailed information Johnnie! To replace you jet ski trailer's hub, I recommend the CE Smith Trailer Idler Hub Assembly w/ Case for 2.7K Axles item # CE13315. This pre-greased marine grade hub has a 5 on 4-1/2" bolt pattern and fits 13" wheels. This hub is specifically designed to fit 2,700 lbs axles with BTR spindles like your trailer has. If you have any additional questions go ahead and throw them into the comment box below.
  view full answer...
• Replacement EZ Loader Trailer Hub for Spindle that is 1-1/6 inch in Diameter
  Hey Tyler, yes the CE Smith trailer hub part # CE13315 that you referenced would work for you as this was designed to fit a straight spindle that is 1-1/16 inch in diameter. This has the very common 5 on 4-1/2 bolt pattern too. If you have a 5 lug bolt pattern most likely this is correct but if not let me know.
  view full answer...
• Do you Carry a Hub with Inner and Outer Bearing L44649 and Grease Seal Inner Diameter 1.25"?
  Hello Chris, Yes, we do have a hub that will work for you the CE Smith Trailer Idler Hub Assembly w/ Case for 2.7K Axles - 5 on 4-1/2 - Galvanized - Pre-Greased # CE13315, or cast iron # CE13311. This hub has both inner and outer bearing L44649, and grease seal is 1.249" inner diameter and 1.983" outer diameter. What kind of bikes are you hauling with your Kendon trailer?
  view full answer...
• What Grease Is Compatible With the CE Smith Trailer Idler Hub # CE13315?
  The CE Smith Trailer Idler Hub Assembly # CE13315 comes pre greased with a marine formula grease. We have the LubriMatic Marine Trailer Wheel Bearing Grease # L54FR that is compatible with the grease in the hub. You will need a Mini Grease Gun # 30-800 to use the smaller 3oz cartridges.
  view full answer...
• Can I Swap The 12" Wheels On The CE Smith Multi Sport Trailer CE48870 To 13" Wheels?
  Though it is possible to upgrade the wheels on the CE Smith Multi Sport Plus Boat and Kayak Trailer # CE48870 to a 13" option, like the Kenda Karrier ST175/80R13 Radial Trailer Tire with 13" Galvanized Wheel # AM31994, it will have to be a separate purchase and cannot be swapped out by us. This is kitted together from CE Smith and isn't something we can change parts on, unfortunately. I do also have to mention that going with a larger tire/wheel will require a few things to be done. First,...
  view full answer...
• Correct Replacement Hub For Jet Ski Trailer With BT150 Hub
  I would be happy to help! Based on the BT150 stamped in your hub you will need the CE Smith Trailer Idler Hub Assembly # CE13315 which includes inner and outer bearings # L44649. This hub comes pre-greased and ready to install on the spindle of your Jet Skit Trailer making it a very easy option. I included a video of the # CE13315 for you to take a look at.
  view full answer...
• Trailer Idler Hubs With L44649 Inner and Outer Bearings And 1-1/4 Grease Seal
  You will want either the CE Smith Galvanized # CE13315 or Black # CE13311 idler hub assemblies. These both have the 1-1/16" ID bearings # L44649 and include grease seals for your 1-1/4" spindle diameter.
  view full answer...
• Replacement Hub Assembly For EZ Loader Trailer Hub 300-020883
  You will need the CE Smith Trailer Hub Assembly # CE13311 for a replacement hub on your EZ Loader Trailer with hub 300-020883. Your hub uses a grease seal that has an inner diameter of 1.249". The CE Smith Trailer Idler Hub Assembly # CE13315 that you found has a grease seal that has a 1.50" inner diameter.
  view full answer...
• Identifying Nut Used For Hub Installation On Boat Trailer With AutoFlex-Knott Axle
  What you have there is a Knott axle with Knott hubs. The bearings in these hubs are sealed so you won't be able to grease your bearings. It is also secured with a one time use flange nut so if you remove it you will have to replace it with a new one to reinstall your hub assembly. If you need to replace the sealed bearings or removed that flange nut you will have to get the replacement parts from the manufacturer. If you want to replace the hubs with a traditional hub assembly you would...
  view full answer...
  
• Replacement Hubs for a 1998 Tracker TrailStar Boat Trailer
  With a 5 1/2 bolt pattern and the outer bearing being an # L44649, you most likely have Dexter's #84 Spindle. This uses the # L44649 (1.063 inner diameter) outer bearing and the # L68149 (1.378 inner diameter) as the inner bearing. This is one of the most common spindles out there, but it wouldn't hurt to verify your inner bearing's inner diameter just to make sure. If all that matches, the etrailer.com Trailer Idler Hub Assembly for E-Z Lube Axles # AKIHUB-545-35-G-EZ-K will be a great...
  view full answer...
• Replacement Hubs for EZ Loader Model EZNB 14-17 1650 Boat Trailer
  The correct galvanized replacement hubs for your EZ Loader EZNB 14-17 1650 trailer are # CE13315. The hub includes bearings, races, the grease seal, replacement cotter pin, dust cap and lug nuts.
  view full answer...
• Replacing Trailer Axle Spindle From Older Short Spindle To BTR E-Z Lube Spindle
  It sounds like you have an older style trailer axle with the short spindles. You will need a new Spindle # TRU44FR to mount on your axle as the short hubs are now obsolete. This will allow you to use the what is now standard length spindle dimensions. The CE Smith Trailer Idler Hub Assembly w/ Case # CE13315 is designed to fit the newer BTR spindles that are more commonly found on trailers.
  view full answer...
• Which Replacement Hub for Shoreland'r SLR22L Boat Trailer
  According to Shorlandr, your SLR22L trailer uses hubs with a L44649 inner and outer bearing. The # CE13511 hub you mentioned uses a different inner bearing, so it won't work for you. The good news is that the # CE13311 is the correct hub, assuming your existing hub has a 5 lug on a 4-1/2 inch bolt circle. Or, even better, since it's a boat trailer we offer a corrosion resistant galvanized version of the 5 on 4-1/2 as well, available as part # CE13315. The replacement hubs include 1/2-20...
  view full answer...
• Determining Correct Replacement Hub For Karavan Single Jet Ski Trailer W/ Single Axle and 13 Wheels
  I would be happy to help! To determine the correct replacement idler hubs for your Karavan single jet ski trailer with a single axle you will need to determine the bearing combination your spindle uses. The easiest way to do this is by removing one of your current hubs and looking for the bearing numbers stamped in the face of both the inner and outer bearings as shown in the included picture of the # L44649. If your bearings are worn to the point that you cannot read the bearing numbers...
  view full answer...
  
• Recommended Hub for a Boat Trailer w/ L44649 Inner and Outer Bearings
  The bearings that go on a 1.06" spindle are item # L44649. These are found in this configuration on 2,000 lbs - 2,700 lbs axles. If you can find it there is typically an axle tag or engraving somewhere on the axle that'll have a serial number or even the capacity on it. To replace the hub you will need one of the following depending on your bolt pattern: 4 on 4 - Galvanized - item # AKIHUB-440-2-G-2K 5 on 4-1/2 - Galvanized - Item # CE13315 Feel free to email me back with any additional...
  view full answer...
• Pre-Greased Hub Assembly with L44649 Inner and Outer Bearings
  We have exactly what you need! For a pre-greased hub assembly that features the same inner/outer # L44649 bearings and races we have the CE Smith # CE13311 or # CE13315 for a galvanized finish (corrosion resistance). These idler hubs come pre-lubricated with heavy-duty grease and all the bearings, races, and seal are included. The hub features a 5 on 4-1/2 inch bolt pattern, which is likely what you have. I have attached a great article on measuring bolt patterns so you can be sure.
  view full answer...
• Replacement Idler Hub for Continental Boat Trailer
  When I did a google search on the 125197250 number you provided, it keeps taking me to the L44649 bearing. is the surface of the spindle that the inner and outer bearing ride upon the same diameter? You could take a digital caliper like # PTW80157 on the spindle surface where the 125197250 bearing rides. If it's right around 1.06 inches, then it's a L44649 bearing. Different manufacturers can refer to the same bearings using different reference numbers. If the spindle doesn't have a taper...
  view full answer...
• Replacing Short Hubs On A 1996 EZ Loader Trailer With Straight Spindles
  It does sound like your bearings are a # L44649 (1.063" inner diameter). If they are original to the trailer they may be pretty worn, which is why your measurements may be off by a few hundredths. Also the seal # 34823 that can be used with the hub # CE13311 is a 1.249" ID so I think we are on the same page there. The hub # CE13311 uses the correct bearings and seal, but it is is 4 1/8" from the outside of the inner bearing to the outside of the outer bearing. Virtually all of the hubs...
  view full answer...
  
• How To Find Replacement Idler Hub for Load-Rite Trailer with 2,700 Lb Axle
  The most likely replacement trailer hub we have available for a 2,700 lb axle is the CE Smith Trailer Idler Hub Assembly part # CE13315. This hub uses L44649 bearings which have an inner diameter of 1.063" and a 10-9 grease seal which has an inner diameter of 1.250". In order to confirm this is correct you will need to verify this as I don't have a way to look up what you have now. In regards to the bolt pattern, this will be the standard 5 on 4-1/2". I have attached an article that shows...
  view full answer...
• Replacement Hub For 2003 EZL90B 15-16 2100 NB EZ Loader Boat Trailer
  The CE Smith Trailer Hub Assembly # CE13315 is the correct replacement hub for your EZ Loader trailer. This hub has the same 5 on 4-1/2" bolt pattern, using the Bearing # L44649 and Grease Seal # 34823 (1.249" ID). Your hub will have a threaded cap while this one will include a standard grease cap. You can upgrade this to the Bearing Buddy Bearing Protectors # BB1980A-SS to easily fill your new hubs with grease without overfilling them and blowing out the grease seal.
  view full answer...

Do you have a question about this Trailer Hubs and Drum?